christmas gifts for dad How to Make a Pacifier Pocket decorative pillow shams

Updated: 2020/03/29 Views: 92

End the hunt for your baby’s binky! This handy, easy-to-make pacifier pocket keeps the pacifier handy and, just as important to fastidious moms, clean. Personalize it with wild and playful colors to reflect your sense of style or your baby’s unique personality. A great and thoughtful gift for a new mom, too. When the crying startschristmas gifts for dad, you’re only a snap away from contentment.

Read all of the pattern instructions before beginning. This will help you plan how to orient your fabric.

accent pillow case baby burlap floor

All seam allowances are 1/2″;.

Supplies

Step 1) Prepare the fabric pieces.

Print the pattern pieces:?pacifier_pocket_pattern_pieces_121814.pdf

Cut the fabric and interfacing:

Fuse a piece of interfacing to the wrong side of each fabric piece, taking care to place the adhesive side of the interfacing against the fabric (and not the iron or ironing board!).

Step 2) Sew the Main Pocket pieces together.

Line the top of the Center Strip up with the top of one of the Main Pocket pieces, with right sides together. Sew the Center Strip to the Main Pocket piece by sewing along the outer edge of the Main Pocket with a 1/4″;-wide seam allowance. You’;ll need to stop and readjust as you’;re sewing, easing the Center Strip around the curve of the Main Pocket piece. If the Center Strip extends past the Main Pocket, trim away the excess so the edges match.

Attach the other Main Pocket piece to the other edge of the Center Strip, easing the Center Strip around the curves.

The three pieces stitched together should look like this:?

Zigzag around each edge, and then trim off any excess fabric.?

Repeat the previous steps to join the lining fabric pieces together.

Step 3) Assemble the Flap and Strap

Place the two Pocket Flap pieces right sides together. Stitch them together along the curved edge using a 1/4″;-wide seam allowance.?

Fold the Strap in half lengthwise, with right sides together. Sew along the long edges with a 1/4″;-wide seam allowance, leaving both ends open.

Eliminate some of the bulk in the seam allowances by cutting notches along the outer curved edge.

Turn the Pocket Flap and Strap right-side out. Iron flat.

Step 4) Construct the Pocket and Flap.

Turn the outer fabric Pocket right-side out. Pin the raw edges of the Pocket Flap to the pocket with the outer fabrics facing each other, being sure to center the flap along one side of the pocket.

Pin the Strap to one side of the tote, centering it along the Center Strip. Make sure the seam of the strap is facing outward.

Slide the Outer Pocket, right-side out, into the Lining Pocket, wrong-side out. The right sides of each piece will be facing each other.

Slide the Outer Pocket completely into the Lining Pocket so the upper edges are even.

Stitch around the upper edge of the Pocket using a 1/4″;-wide seam allowance. Make sure you catch the Flap and Strap pieces in the stitching, and leave about 1-1/2″; open along the side opposite the Flap. (You’;ll turn it right side out through this opening later.)

Begin turning the Pocket right-side out through the opening.

Pull out the outer fabric first.

Then push the lining fabric back toward the inside.

After you poke out and straighten all the Pocket edges, tuck the seam allowances of the opening to the inside and pin it closed.

Sew all the way around the upper edge, nice and close to the edge. This stitching keeps the upper edge in place and also closes the opening –?no hand stitching required!

Step 5) Finish the Strap and Snaps

Zigzag the raw edge of the Strap to prevent fraying.

Attach snaps to the Flap and the front of the Pocket.

Attach snaps to the end of the strap and the side of the Pocket.

You’ve seen a few rooms of our little lake cottage here on the blog and glimpses of others on Instagram, but given the amount of time we spend there, I felt #calmwatercottage deserved a tour of it’s own.

When we’re decorating a space, whether it’s in a catalog or for our own home, some things just work. Symmetry is one of those things. A symmetrical arrangement of furniture or art just works, always, which is why we’re constantly using pairs to turn so-so spaces into gorgeous rooms your family can enjoy. Today, we thought we would elaborate on our love for pairs and why you need them in your home.

This DIY Homemade No.2 Poo Spray is like store-bought PooPourri Toilet Spray, but customizable. Made with essential oils, glycerine and a couple of other household ingredients it’s really easy to make. Add this free printable label with simple instructions as to how to use it and you’re set! Speaking of free printables, you may also like this printable bathroom wall art if you’re looking to add inexpensive decor.